







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Driveway & Pavers: The Long Beach Owner’s Guide
Schluter isn’t a paver brand, and that’s the first thing to sort out. Schluter Systems makes the substrate and edge-protection layers that sit under and beside driveway and paver work (DITRA and DITRA-XL uncoupling membranes, KERDI waterproofing, SCHIENE and TREP-E edge profiles, and the DILEX and QUADEC transition pieces), so the “part” that’s failing is almost always a membrane, a profile, or a movement joint rather than the stone itself. Installed repair and replacement work in Long Beach typically falls into the paver driveway installation range of $7,000 – $18,000 for full rebuilds, or a far smaller line item when it’s a membrane swap or profile reset under an existing concrete edge.
Owners usually find the problem the same way: a paver or two lifts near the driveway apron and the sand underneath is wet and loose, a SCHIENE edge profile has started to separate from the concrete curb, or a hairline crack runs along the fillet where the driveway meets the garage slab. That’s the substrate telling you something, not the pavers.
Which Schluter Models This Apply To

Match the part to the job before you buy anything. The key compatibility gotcha on driveways is load rating: DITRA and DITRA-XL are uncoupling membranes designed for interior tile and thin-set assemblies, not for a driveway carrying a 4,000-pound SUV, so a residential driveway edge or apron detail is where profiles and drainage matter far more than uncoupling membrane. DITRA-XL gives you roughly 5/16 inch of build height versus DITRA’s 1/8 inch, and mixing them mid-run creates a lip you’ll feel through the tires.
To identify what you actually have, pull the manufacturer label from the original installation box if it survived, or measure the profile: SCHIENE comes in heights from about 1/4 inch to 3/4 inch in roughly 1/16-inch steps, and TREP-E steps in similar increments with a wider anchoring leg. Edge profiles are sold in 8-foot and 10-foot lengths in aluminum, stainless, and PVC, and the height must match your paver thickness, not your concrete thickness. On the OEM-versus-aftermarket question, Schluter’s own profiles are the safe choice for a driveway because the stainless and aluminum grades are specified for exterior exposure. A generic aluminum trim from a big-box aisle will look fine for two summers and chalk out in the salt air.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Driveway & Pavers Is Failing
- An edge profile lifting away from the concrete. The anchoring leg has lost its thin-set bond, usually because the concrete was damp or dusty at install. Water gets behind the profile and the gap widens each wet season.
- Loose or rocking pavers at the driveway apron. Sand has washed out under the base layer, often where Long Beach’s winter rain sheet-flows off the garage slab. The pavers aren’t the problem; the drainage detail is.
- A crack tracking along the transition strip. The movement joint wasn’t wide enough, so thermal expansion from a 90-degree August pushed the pavers into the curb. Long Beach’s temperature swings are modest but the sun load on a west-facing driveway is not.
- White chalky residue or rust bleed on aluminum profiles. Salt air near the water and the alkaline chemistry of fresh concrete both attack bare aluminum. Stainless profiles handle it; aluminum ones stain and eventually pit.
- Standing water in a low corner after rain. The base slope drifted from the required 1 to 2 percent away from the structure, and the membrane or drainage mat under the pavers is now holding water instead of shedding it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s the honest number structure for Long Beach. A profile swap or membrane repair under an existing edge usually runs as a small line item inside a driveway repair; a full paver driveway installation runs $7,000 – $18,000, and driveway replacement of an existing surface runs $5,000 – $14,000. If the failure has undermined the base and you’re rebuilding, concrete driveway installation sits at $4,500 – $12,000 and asphalt paving at $3,500 – $9,000.
What drives the range up: linear footage of edge profile, whether the base layer needs re-grading, stainless versus aluminum profiles, and access for equipment on a narrow lot. What’s included on our jobs: written price before any work starts, the profile and membrane materials itemized, tear-out and haul-off, and our 365-Day Done Right Promise in writing. If the repair fails inside the guarantee period, we come back and fix it at no charge.
DIY or Call Us?
You can safely check a few things yourself: pull up a loose paver and look at the sand, measure your profile height with a tape, photograph the transition joint, and note whether water pools after rain. Those notes make the estimate faster.
Where DIY goes wrong is at the structural end. Resetting an edge profile means cutting back the adjacent paver or concrete, re-establishing the thin-set bond on a properly prepared substrate, and keeping the profile height dead-flush with the paver surface. Get it a sixteenth off and you’ve created a tire-catching lip. Rebuilding a base layer means knowing the compaction spec and the drainage slope, and a driveway that fails again in two winters costs more than doing it once. Our technicians have up to 22 years of experience on exactly this, and the first visit and estimate are free. Call (833) 510-6967 and we’ll give you a written number before anyone picks up a tool.
FAQs

How long should a Schluter edge profile last on a driveway in Long Beach? A stainless or properly specified aluminum profile set in a sound base typically holds 10 to 15 years in Southern California; PVC profiles and cheap aluminum in salt air often fail in under 5. The profile isn’t the weak link most of the time, the base and drainage are. Call (833) 510-6967 for an exact assessment.
Can the part be repaired instead of replaced? Often yes. A lifted profile can be re-bonded and a single washed-out section re-graded without touching the rest of the driveway. If the base under more than a few square feet has failed, a local repair just moves the problem down the line. We’ll tell you which one you’re looking at.
How long does the swap take? A profile reset is usually a half-day to a full day. A paver section rebuild runs two to four days depending on square footage and whether the base needs re-compaction. We give you a real arrival window, not a “sometime Tuesday.”
How do you source the Schluter part? We specify the correct profile height and material grade for your paver thickness and exterior exposure, then source it through authorized Schluter distributors. We’re an independent service provider and not affiliated with Schluter, so you get an honest recommendation on OEM versus a quality aftermarket equivalent, not a sales pitch. Call (833) 510-6967 for a free estimate.
We also work with KraftMaid, Cambria, and Silestone on the interior side of the house when a driveway project turns into a whole-home conversation.
Ready to get a written price on your Long Beach driveway and paver work? Call Penhallow Remodeling Long Beach at (833) 510-6967 for a free estimate. A live person answers around the clock, our technicians arrive in uniform and background-checked, and you’ll have the number in writing before work starts.
Written by the team at Penhallow Remodeling Long Beach, serving Long Beach and nearby areas.












