







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Driveway & Pavers: The Long Beach Owner’s Guide
We install driveway and paver systems matched to CGI project specs, and a full paver driveway in Long Beach typically runs $7,000 – $18,000 installed. Concrete alternatives sit at $4,500 – $12,000, and paver patios land between $3,500 and $11,000. Replacement work is scheduled by appointment, usually within a week or two, and every project starts with a written price before any work begins.
Owners usually spot the problem the same way. First comes the sunken corner where the car tires track, then the joint sand washing out after a winter rain, then a paver that rocks underfoot when you walk to the mailbox. By the third rainy season in Long Beach, a driveway that looked fine at purchase starts showing its base.
Key Takeaways
- CGI specs vary by paver series and thickness, so the match is made from measurements, not guesswork.
- Long Beach’s marine air and sandy coastal soil are hard on joint sand and base compaction.
- Written pricing, a defined arrival window, and the 365-Day Done Right Promise on every job.
- Live phone coverage 24/7 with a real person, not a callback window.
Which CGI Models This Applies To

CGI paver systems are specified across interlocking driveway and patio lines, and the compatibility question is almost never about “the brand” as a whole. It’s about the series, the nominal thickness, and the laying pattern the project was set to. Most residential driveways use a paver in the 2 3/8-inch to 2 3/4-inch range for vehicle loads, while patios often run the thinner profile. If you’re matching an existing run for a repair or expansion, the thickness matters before anything else: a replacement course that’s even a sixteenth off will telegraph through the surface within a season.
To identify the right match, we look at the color name on the original paperwork if you have it, then measure a single paver edge to edge (length, width, thickness) with a tape. Chips and faded units give us the color family even when labels are gone. On the OEM-versus-aftermarket call, there’s a real decision here. A CGI-spec replacement is the surest route when you’re tying into an existing field and want the joints to line up. A quality aftermarket paver from a recognized line (Belgard and Unilock both make compatible profiles) can work for a full replacement where color and dimension are re-set together, and often costs less per square foot. We don’t carry stock and don’t stock parts on a truck, so we source to your project once we’ve confirmed the spec. We’re an independent remodeling company, not affiliated with CGI.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Driveway & Pavers Is Failing
- Sunken or rocking pavers at the tire tracks. That’s base failure, not a loose stone. The compacted gravel underneath has settled or wasn’t deep enough to begin with, and no amount of re-sanding fixes it.
- Joint sand washing out after rain. Long Beach’s winter storms push water through open joints, and once the sand is gone the pavers shift against each other. Refilling helps briefly, but repeated washout points to a drainage or slope problem.
- Weeds and ant trails between pavers. Persistent growth means the joint sand has eroded and moisture is sitting where it shouldn’t. It’s the first visible sign that the interlock has loosened.
- Efflorescence (the white chalky haze). That’s mineral salt drawn to the surface, common in coastal Long Beach air. Occasional haze is normal; recurring bloom says water is moving through the system.
- Heaving or a humped section. Usually a tree root or a base that wasn’t excavated deep enough. This one gets worse each season and can crack the pavers above it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what the numbers look like in Long Beach, with the install and the prep included:
| Service | Installed range (Long Beach) |
|---|---|
| Paver driveway installation | $7,000 – $18,000 |
| Concrete driveway installation | $4,500 – $12,000 |
| Asphalt driveway paving | $3,500 – $9,000 |
| Driveway replacement | $5,000 – $14,000 |
| Driveway sealing | $250 – $700 |
| Paver patio installation | $3,500 – $11,000 |
What pushes you toward the top of the range: deeper base excavation, a larger square footage, a premium paver line, and drainage correction on a slope. What keeps it lower: a straightforward rectangle with good existing drainage. The written price includes removal and haul-off of the old surface, base compaction, edge restraint, joint sand, and cleanup. Our 365-Day Done Right Promise covers the work in writing, and if something fails inside that year, we come back and fix it at no charge.
DIY or Call Us?
There’s a safe middle ground. You can measure your existing pavers, photograph the failing area, check for pooling water after a rain, and pull the original paperwork. Those things help us quote accurately. What goes wrong in DIY is the base and the compaction: homeowners lay pavers on a thin sand bed and skip the compacted gravel layer, and within one Long Beach wet season the surface dips and the joints open again. It’s less dangerous than electrical or high-tension work, but the failure shows up fast and costs more to undo. For drainage correction on a slope or full replacement, hand it to a crew. Call (833) 510-6967 for a written price before anything starts.
FAQs

How long do CGI driveway pavers last in Long Beach? A properly installed paver driveway lasts 25 to 50 years when the base is compacted and joints are maintained. Long Beach’s coastal salt air and sandy soil shorten that if drainage isn’t handled, so expect to re-sand joints every couple of years regardless of the paver brand.
Can the driveway be repaired instead of replaced? Often yes. Isolated rocking pavers or a small settled section can be lifted, the base re-compacted, and the pavers reset, which costs a fraction of a full install. If more than a quarter of the surface is moving or the base was never deep enough, replacement is the honest answer. Call (833) 510-6967 and we’ll tell you which one you’re looking at, with a written price either way.
How long does a paver driveway swap take? A typical Long Beach driveway takes three to six working days once materials are on site: one to two for demo and haul-off, one to two for base and compaction, and the rest for laying, edge restraint, and joint sand. We give you a defined arrival window up front and keep the job site clean throughout.
How do you source the right CGI-match pavers? We confirm the series, thickness, and color from measurements and any remaining paperwork, then source from recognized trade lines including Belgard and Unilock where a compatible profile fits. You get the spec and the price in writing before we order anything.
When you’re ready to get a real number for your driveway, we’re here. Call Penhallow Remodeling Long Beach at (833) 510-6967 for a free estimate, a written price before work starts, and the 365-Day Done Right Promise behind the job. A live person answers 24/7, our technicians are background-checked and arrive in uniform, and technicians here have up to 22 years of experience. We also work with lines like KraftMaid, Cambria, and Silestone on the interior side.
Written by the team at Penhallow Remodeling Long Beach, serving Long Beach and nearby areas.












