







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Dvele Bathroom Remodeling: The Long Beach Owner’s Guide
Dvele bathroom components in Long Beach are modular, factory-built parts, and when one fails you replace the part, not the room. Typical installed bathroom remodeling in Long Beach runs $9,000 – $28,000, while a single failed component (a vanity, a shower pan, a mixing valve) usually lands in the low four figures. We install Dvele-compatible bathroom assemblies and finish work across Long Beach. Our technicians have up to 22 years of experience, and every job starts with a written price before any work begins.
Owners usually find out the hard way. A vanity drawer front delaminates after two coastal summers, the shower pan flexes underfoot and cracks at the drain flange, or the faucet cartridge stops holding temperature and the handle spins without resistance. Dvele builds to modular tolerances, which means the replacement has to match the module, not the nearest big-box part. That’s the whole game here.
One clear note: Penhallow Remodeling Long Beach is an independent contractor. We’re not affiliated with Dvele, and we don’t speak for them. We source compatible parts and install them to spec.
Which Dvele Models This Applies To

Dvele’s bathroom modules come out of distinct model lines, and the part that fits one won’t fit another. The identifying plate is usually inside the vanity cabinet on the back panel, or on a sticker under the sink basin. It lists the model and series code, and that code is what you match against before ordering anything.
Three compatibility gotchas we see on Long Beach jobs:
- Vanity cabinet width is nominal, not actual. A “48-inch” Dvele vanity may measure 47.25 inches at the box. Ordering a stock replacement countertop cuts it too short. We measure the box, not the label.
- Shower pan drain centers vary by series. Dvele pan drain centers run roughly 11 to 14 inches from the rear wall depending on the model line. A pan with the wrong offset means re-plumbing the drain, which turns a swap into a real project.
- Faucet rough-in spacing changed across generations. Earlier modules used a narrower spread than current ones. The cartridge and trim you order has to match the valve body already in the wall, not the faucet style you liked in a photo.
On OEM versus aftermarket: for structural parts (shower pans, valve bodies, cabinet boxes), OEM or a certified equivalent is the right call. For trim (faucet aerators, drawer slides, cabinet pulls, silicone seals), a quality aftermarket equivalent from Kohler, Moen, Delta or Grohe is fine and often better made. We’ll tell you which side of that line each part falls on. We also install KraftMaid and Wellborn cabinetry, Cambria and Silestone countertops, and Kohler and Moen fixtures where a full component replacement makes more sense than a patch.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Dvele Bathroom Remodeling Is Failing
These are the failures Long Beach owners call us about, and what’s actually happening underneath.
- The shower pan flexes or clicks underfoot. That’s a failed mortar bed or a cracked pan flange. Coastal humidity accelerates it, and a flexing pan will leak into the floor assembly within a season or two.
- Water stains at the base of the vanity. Usually a failed silicone seal or a slow valve-body drip behind the cabinet back. By the time you see the stain, the cabinet floor is already swelling.
- The faucet cartridge won’t hold temperature. Mineral scale in Long Beach’s harder water supply eats cartridge seals. The handle drifts hot on its own or won’t shut off cleanly.
- Tile grout cracks in a straight line. A straight-line crack almost always means substrate movement, not grout failure. Re-grouting it is a temporary fix; the cement board underneath needs checking.
- The exhaust fan runs but the mirror still fogs. A clogged or undersized fan or a duct that terminates in the attic instead of outside. Trapped moisture is the root cause of most of the failures above.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed bathroom remodeling in Long Beach runs $9,000 – $28,000. A small bathroom remodel runs $5,000 – $12,000. A single component swap sits lower:
| Job | Installed range in Long Beach |
|---|---|
| Bathroom remodel (full) | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
| Vanity installation | $800 – $3,000 |
What drives the number up: drain relocation when the new pan’s offset doesn’t match, substrate repair behind tile, and valve-body replacement (which means opening the wall). What keeps it down: matching the original module dimensions and reusing sound substrate. Every price we give is written before we start, and the number on day one is the number on the invoice. The 365-Day Done Right Promise backs the work in writing, and if something fails inside that period we come back and fix it at no charge.
DIY or Call Us?
Some of this you can safely check yourself. Pop the vanity door and read the model plate. Measure the cabinet box, the countertop depth, and the drain center-to-rear-wall distance. Run the faucet and watch for a slow drip behind the cabinet. Those checks cost nothing and tell us exactly what part to bring.
Where DIY goes wrong: anything behind the wall. Replacing a valve body means shutting off water, opening the wall, and sweating or pressing new fittings. A leak inside a wall in a Long Beach condo can reach the unit below before you notice it. Shower pan replacement means removing tile, checking the substrate, and re-waterproofing to spec. If you get the waterproofing wrong, the leak returns in months. And if the exhaust fan duct is the real problem, swapping the fan won’t fix it.
If you’re not sure which side of that line you’re on, call (833) 510-6967. A written price is free, and we’ll tell you if it’s a ten-minute fix you can do yourself.
FAQs

How long does a Dvele bathroom part usually last? Most Dvele bathroom components last 10 to 15 years in a well-vented room, but in Long Beach’s coastal humidity that drops to 7 to 10 years for pans and cabinet boxes if the exhaust fan isn’t moving air outside. Ventilation is the single biggest factor.
Can the part be repaired instead of replaced? Sometimes. A faucet cartridge, a drawer slide, a silicone seal and a failed exhaust fan are all repair jobs, and we’ll quote repair first if it makes sense. A cracked shower pan or a leaking valve body gets replaced, because a patch on either one fails again. Call (833) 510-6967 and we’ll tell you honestly which one you’re facing.
How long does the swap take? A vanity or faucet swap runs half a day. A shower pan replacement typically runs two to four days because the tile, substrate and waterproofing all have to come out and go back correctly. We give you a defined arrival window and a written schedule before we start.
How do you source the part? We match the model code off your plate against the Dvele part spec, then order OEM or a certified equivalent depending on the component. We don’t carry parts on a truck and we don’t keep stock, so ordering is part of the timeline, and we tell you the lead time up front. If an aftermarket equivalent from Moen, Delta or Grohe is a better part for the money, we’ll say so before you commit.
Call (833) 510-6967 for a free estimate. A live person answers, every time. Technicians are background-checked and arrive in uniform, and you’ll have a written price before any work starts.
Written by the team at Penhallow Remodeling Long Beach, serving Long Beach and nearby areas.












