







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Moen Bathroom Remodeling: The Long Beach Owner’s Guide
We install Moen-compatible bathroom remodeling in Long Beach, and most full bathroom remodels run $9,000 – $28,000 installed, depending on layout, tile, vanity and fixture line. Smaller projects like a vanity swap or shower replacement start lower, and we give you a written price before any work begins so the number on day one matches the invoice. If you have a Moen fixture that’s dripping, sticking or leaking behind the wall, we can usually schedule an assessment within a day or two – call (833) 510-6967 and a real person answers, any hour.
Owners usually find the problem the same way: a slow drip at the tub spout that never stops, a handle that turns but won’t shut off cleanly, or a water stain blooming on the ceiling below. In Long Beach’s older housing stock – lots of 1920s-to-1960s bungalows in Belmont Shore, Rose Park and California Heights – that stain often traces back to a Moen cartridge or valve that’s been in the wall longer than the tile has.
Key Takeaways
- Full bathroom remodel in Long Beach: $9,000 – $28,000 installed, written price up front.
- We work with Moen fixtures and back every project with our 365-Day Done Right Promise.
- We’re an independent remodeling company – not affiliated with Moen.
- Written guarantee on every job, plus a free return visit if a repair fails.
- Background-checked, uniformed technicians on every project.
Which Moen Models This Apply To

Moen has made a lot of valve families over the decades, and which one is behind your wall changes the whole job. The biggest divide is between the older 1200/1222 and 1225 single-handle cartridges (common in pre-2000 homes) and the newer 1222HD and Posi-Temp lines. Moen’s Posi-Temp valves – found on many shower-only and tub-shower setups – use a pressure-balancing spool that fails differently than a standard cartridge, and the replacement part isn’t interchangeable. Pull the handle and look for a model number stamped on the escutcheon (the decorative plate behind the handle) or on the cartridge itself. If you can’t find it, a photo of the valve body is usually enough for us to identify it.
On the OEM-versus-aftermarket question: Moen’s own replacement cartridges carry a limited lifetime warranty in many cases, but generic aftermarket cartridges sold at big-box stores are often a few thousandths of an inch off-spec, which is enough to cause a slow drip or a stiff handle within a year. For a fixture that’s going back behind new tile, we recommend the OEM part. When we quote a Long Beach bathroom remodel, we source fixtures and parts from recognized brands including Moen, Kohler, Delta and Grohe, alongside cabinetry from KraftMaid and stone from Cambria or Silestone. We don’t stock parts or carry them on a truck – we source the right part for your model before we open the wall.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Moen Bathroom Remodeling Is Failing
Moen fixtures are reliable, but they do age, and Southern California’s water chemistry (Long Beach runs moderately hard, roughly 8-12 grains per gallon depending on the zone) accelerates cartridge wear. Here’s what owners typically notice:
- A drip that won’t stop at the spout or showerhead. The cartridge’s internal seals have worn, letting water past the closed position. In hard-water areas this often starts as a slow weep and worsens over months.
- The handle turns stiffly or feels gritty. Mineral scale has built up on the cartridge stem, or the balancing spool is sticking. Left alone, this can eventually crack the cartridge housing.
- Temperature swings in the shower. On a Posi-Temp valve, this usually means the pressure-balancing spool has failed, so the valve no longer compensates when someone flushes a toilet nearby.
- Water staining on the ceiling below the bathroom. A failed valve body or a loose connection behind the wall is leaking. This one needs attention promptly – drywall and framing damage compounds fast in a coastal climate.
- Rust or corrosion at the escutcheon or valve trim. Long Beach’s marine air speeds up corrosion on older trim. Surface rust is cosmetic; corrosion creeping onto the valve body is not.
Replacement Cost & What’s Included

Here’s what bathroom work runs in Long Beach, with real numbers:
| Project | Installed Range |
|---|---|
| Full bathroom remodel | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
| Bathroom vanity installation | $800 – $3,000 |
What pushes a Long Beach bathroom remodel toward the top of the range: relocating the drain or supply lines, tile over a failed substrate, or discovering a valve that needs access through finished wall. What keeps it lower: keeping the existing layout and reusing the rough-in. Our quotes are line-item and separate labor from materials, so you can see exactly what the Moen fixture and any valve work costs versus the tile and vanity. Every project carries our 365-Day Done Right Promise – if the work fails inside that year, we come back and fix it at no charge, in writing.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Some of this you can safely check yourself. You can look for the model number on the escutcheon, test whether the drip stops when you shut the supply valves, and check for visible corrosion. What you shouldn’t do is open a wall to swap a valve body, or try to force a seized cartridge out of an old rough-in – a broken valve body means water where it doesn’t belong, and in a house with galvanized or aging copper supply lines, the surrounding plumbing can be fragile enough that a wrong turn turns a $30 part into a wall repair. Shower valve work sits behind tile and in tight, wet spaces; it’s the kind of job where a trained professional pays for themselves. If you want a straight answer on whether your Moen setup needs a part swap or a fuller remodel, call (833) 510-6967 and we’ll tell you honestly.
FAQs

Most Moen cartridges last 10-15 years before the seals wear enough to drip, though Long Beach’s moderately hard water can shorten that to 8-10 in homes without a softener. If yours is older than that and dripping, replacement is usually the fix rather than a valve rebuild.
Sometimes. A stiff handle can often be cleaned of scale and re-greased, and a slow drip occasionally responds to a new cartridge O-ring. But if the valve body itself is corroded or the balancing spool on a Posi-Temp has failed, replacement is the reliable fix. We’ll tell you which you’re looking at after we see it – call (833) 510-6967 for a free estimate.
A cartridge replacement on an accessible Moen valve typically takes 1-2 hours once the part is in hand. If the valve body needs replacement and it’s behind tile, the job becomes a shower or tub-surround repair and can run a day or more, which is why we quote it in writing before we start.
We identify your valve model from the escutcheon stamping or a photo of the valve body, then source the OEM replacement for that exact valve family. We don’t stock parts and don’t carry them on a truck, so the part is ordered to your model – not matched by guesswork at the door.
Get a Written Price for Your Long Beach Bathroom
If a Moen fixture is failing behind your wall, or you’re ready to plan a full bathroom remodel in Long Beach, we’ll give you a written price before any work starts and back it with our 365-Day Done Right Promise. Our technicians are background-checked and arrive in uniform, and a real person answers our line around the clock. Call (833) 510-6967 to schedule your free estimate – estimates are free, and the number you get is the number you’ll hold us to.
Written by the team at Penhallow Remodeling Long Beach, serving Long Beach and nearby areas.












