







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Moen Roofing: The Long Beach Owner’s Guide
Moen makes the plumbing fixtures, not the roof over them, so a homeowner searching for “Moen roofing” is usually looking at flashing and vent penetrations around a Moen shower vent, a Moen tub spout on an upper-floor bathroom, or a bath fan termination on the roof deck. Roof repair around those penetrations in Long Beach typically runs $400 – $1,800, and a full roof replacement runs $8,000 – $20,000 depending on square footage, pitch and whether the old layers get torn off. We schedule estimates within a normal arrival window; planned roof work is not a same-day job, and anyone who tells you otherwise is selling you something.
Most owners find the problem after a Santa Ana wind event or the first real rain of the season. A brown ring appears on the ceiling below an upstairs bathroom. Granules start collecting in the gutter. A Moen shower valve gets blamed for a leak when the water is actually coming through a failed boot around the exhaust vent four feet away. We’ve made that diagnosis in Bixby Knolls, in Belmont Shore bungalows with original 1940s framing, and in the newer three-story builds near Downtown where the roof deck is tight and the penetrations sit close together.
One thing to say plainly up front: we’re an independent remodeling company, not affiliated with Moen. We install and repair the roofing and venting around Moen fixtures, and we install Moen, Kohler, Delta and Grohe fixtures in the bathrooms underneath. That’s the whole relationship.
Which Moen Models This Applies To

Moen doesn’t publish a “roofing” line, so there’s no model number on a box to match. What you’re matching is the roof penetration tied to a Moen installation. The common cases:
- Upper-floor Moen shower or tub installations where the vent stack or fixture penetration passes through the roof deck. The roof boot, collar and flashing around that stack is what fails, not the valve.
- Moen bath fan terminations on the roof surface, where the hood or damper assembly has cracked or the seal has dried out.
- Moen-equipped second-story bathroom remodels in older Long Beach homes where the roof was never re-flashed after the bathroom was reconfigured.
How to identify what you’re actually replacing
Go up in the attic, not on the roof, first. Look for a wet or stained area on the sheathing and trace it up. Measure the diameter of the pipe passing through the deck: standard vent stacks run 1.5″, 2″ or 3″. The boot or collar sized for that diameter is the part. On the roof side, the pitch of your roof determines the flashing style, and Long Beach roofs range from nearly flat on mid-century carports and additions to steep on the 1920s Craftsman stock in Rose Park and Bluff Heights. A flashing made for a 4/12 pitch will not seat correctly on a 9/12 roof, and that mismatch is one of the most common causes of repeat leaks we get called back on.
OEM vs. aftermarket flashing
For the roof-side parts, aftermarket is generally fine. Quality EPDM and silicone boots from recognized manufacturers hold up as well as anything branded, and the price difference is small. What matters more than the brand is the material: standard neoprene boots degrade noticeably faster under Long Beach’s UV load than silicone boots do. If you’re paying someone to climb up there, the silicone version is worth the extra few dollars. On the Moen fixture side, use Moen genuine parts when a cartridge or trim piece is the issue, because aftermarket cartridges are the single most frequent cause of the “fixed it and it broke again” callback.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Moen Roofing Is Failing
- Ceiling stains below an upstairs Moen bathroom. Water tracking along the sheathing from a failed vent boot lands several feet from the actual leak, so the stain location and the leak location are rarely the same spot.
- Granules in the gutter or at the downspout outlet. Granule loss is normal aging, but sudden heavy shedding after a hot summer points to a roof surface near the end of its service life. Asphalt shingles in Long Beach’s coastal sun and salt air commonly give 15 – 20 years where a shaded inland roof might run longer.
- Daylight visible in the attic. A pinhole of light along the roof deck is a failed flashing or a lifted nail. This one is worth checking before the rainy season, not after.
- Cracked or missing vent boots and collars. Rubber boots crack from UV exposure and heat cycling. A cracked boot lets water in along the pipe, and the leak shows up as a wet patch on the bathroom ceiling below.
- Water staining or soft spots around the Moen valve wall from above. If the wall behind the shower valve is wet from the top down, the roof above the penetration is the first thing to check, not the valve body.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Installed pricing in Long Beach for the work that actually addresses a Moen-related roof problem:
| Job | Typical installed range |
|---|---|
| Roof repair (flashing, boots, isolated shingles) | $400 – $1,800 |
| Tile roof repair | $600 – $2,500 |
| Roof replacement (asphalt shingle) | $8,000 – $20,000 |
| Metal roof installation | $15,000 – $40,000 |
What drives the number: the size and pitch of the roof, how many layers have to come off, sheathing condition, whether the attic is accessible, and material choice. A simple flashed-boot replacement on an accessible roof sits at the bottom of the repair range. A tear-off on a steep, multi-plane roof over a 1920s Long Beach home with original sheathing sits at the top of the replacement range.
You get a written price before any work starts: a line-item number for the repair or the replacement, not a verbal range. That number doesn’t move once we’ve taken a look, and it doesn’t move when the crew finds a soft panel or a rotted fascia, because we quote those contingencies up front. Every job comes with a written guarantee and the 365-Day Done Right Promise. If the repair fails inside that year, we come back and fix it at no charge, and there’s no service-call fee or re-inspection fee for that return visit.
DIY or Call Us?
Here’s an honest split of what’s reasonable and what isn’t. In the attic, on your feet, with a flashlight: check for water staining, look for daylight, and photograph the underside of the roof deck. That’s safe, and it tells you a lot about the scale of the problem. On the roof is a different story. Ladder work on a two-story Long Beach home, walking a pitched roof, cutting and fitting flashing around a vent stack, and getting the shingle course to seal back down correctly are all jobs where the failure mode is either a fall or a leak that shows up the next time it rains. We see plenty of both. If the roof is more than one story up or steeper than a walkable pitch, stay off it.
One more honest note: the Moen cartridge swap that homeowners often assume is the culprit is itself a job to be careful with, because accessing a cartridge set inside a wall or behind a trim can lead to damaging finishes or the valve body if the wrong tool is used or the trim isn’t seated back correctly. The roof-side fix and the fixture fix are different trades. If both are in play, we’d rather look at it once and tell you which one you’re actually dealing with. Call (833) 510-6967 to set up a free estimate, and a real person will pick up.
FAQs

Most EPDM and silicone vent boots last 10 – 15 years under Long Beach’s UV and salt-air exposure, and silicone boots tend to outlast standard neoprene versions on the coastal side of the city. Asphalt shingles around them commonly run 15 – 20 years. If your roof is older than that and you’re seeing any of the symptoms above, get it looked at before the next rainy season. Call (833) 510-6967 for a free estimate; the number is free and the look is free.
Yes, in most cases. A failed vent boot, a cracked collar, a lifted flashing or a localized shingle failure is a repair in the $400 – $1,800 range and doesn’t require a new roof. Replacement becomes the right call when the decking is soft across a large area, when the shingles are at the end of their life, or when the same area has leaked repeatedly. We’ll tell you which one it is after we look. Call (833) 510-6967 for a written price either way.
A single flashing or boot replacement usually takes a few hours on an accessible roof, and a more involved repair where the decking or multiple penetrations are affected can run a full day. A full roof replacement on a typical Long Beach home is a multi-day job. We give you a written arrival window and a realistic schedule before we start, not a guess. Call (833) 510-6967 to schedule your estimate.
We source flashing, boots and roofing materials from recognized trade brands and match the material to the roof type and the pitch, rather than putting whatever is on hand onto your roof. On the Moen fixture side, we use Moen genuine parts for cartridges and trim, because aftermarket cartridges are a common source of repeat failures. We don’t carry parts on a truck and we don’t stock anything on-site, so the material gets ordered for your job. Same approach on the interior work: KraftMaid and Wellborn cabinetry, and Cambria, Silestone and Caesarstone countertops, ordered to your project and installed under the same written guarantee. Call (833) 510-6967 to get started.
Written by the team at Penhallow Remodeling Long Beach, serving Long Beach and nearby areas.












