







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Bathroom Remodeling: The Long Beach Owner’s Guide
Schluter bathroom remodeling in Long Beach typically runs $9,000 – $28,000 installed, depending on bathroom size, how much tile and waterproofing gets replaced, and whether the existing substrate has to come out. We install Schluter-certified systems (DITRA, KERDI, KERDI-BOARD, DITRA-HEAT, and the shower-specific profiles) on a written price before demo day, and we can usually schedule a free site evaluation within a few business days.
Owners in Long Beach rarely discover failing Schluter installation through a fixture. They discover it through the symptom: a hairline crack tracking along a grout joint on a porcelain floor laid over a plywood subfloor in a 1920s bungalow off Broadway, or a spongy patch underfoot in a 1970s condo bathroom near Belmont Shore after a wet winter. The grout moves, the tile tents, or a shower pan leaks into the wall cavity and shows up as bubbling paint on the other side. That’s when the call comes in.
Which Schluter Systems This Applies To

Schluter isn’t one product. It’s a family of systems, and each fails differently. The ones that come up most in Long Beach bathrooms:
- DITRA and DITRA-HEAT – uncoupling membrane under tile floors. DITRA-HEAT is the version with heating cable set into the mat. If the heating element fails, the floor still works but the heat zone dies.
- DITRA-HEAT-E – the electric floor-warming system with a programmable thermostat. The thermostat and the cable leads are the parts that fail first, not the tile.
- KERDI – the sheet waterproofing membrane behind tile in wet areas. The membrane is fine; the KERDI-BAND at seams and the pipe-seal gaskets are where leaks start.
- KERDI-BOARD – the waterproof backer board used for shower walls and benches. Sizes are 1/2″, 3/4″, 1-1/2″, and 2″ thickness, in 4′ x 8′ or 4′ x 5′ panels. Ordering the wrong thickness for a curb is the most common compatibility mistake.
- KERDI-SHOWER kits – the precut shower pan and drain system. The drain body and the integrated bonding flange are the parts most likely to need replacement.
- SCHIENE, RONDEC, and DILEX – the metal edging and movement profiles at tile perimeters. These wear visually, not structurally.
To identify what you have: check the inside face of your shower drain cover (most say “Schluter” or “Kerdi-Drain” on the flange), measure your wall board thickness with a tape at an unfinished edge, and look at the mat print on any exposed floor membrane. Match the series, not the color – the color of SCHIENE edging is decorative; the profile number (e.g., SCHIENE-E 1/2″) is what determines fit.
OEM vs. aftermarket: Schluter is closed-system. There is no meaningful third-party aftermarket for KERDI-BAND, KERDI-BOARD, or DITRA-HEAT cable. Non-Schluter “equivalents” exist (generic waterproofing membranes, generic uncoupling mats), but they aren’t cross-compatible with a Schluter drain or Schluter band. If your existing system is Schluter, the replacement part is Schluter. If your system is generic, we tell you that plainly before quoting.
One thing to know: Penhallow Remodeling Long Beach is an independent service provider. We’re not affiliated with Schluter Systems; we install and repair the products because they’re the industry standard, not because we represent them.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Bathroom Remodeling Is Failing
Here’s what actual failures look like in Long Beach bathrooms – and what’s underneath each one:
- Grout cracks tracking along tile joints. The uncoupling layer (DITRA) is doing its job if the tile doesn’t crack too. If it’s a straight crack following the joints, the membrane may have been installed without enough fleece contact or over a subfloor that deflects. Long Beach pier-and-beam homes flex more than slab homes; we see this most in older Belmont Heights and Rose Park bungalows.
- Hollow or loose tile near the shower edge. KERDI-BAND at the transition to drywall is peeling because the thin-set underneath cured too dry in dry Southern California air. Once the band opens, water wicks behind the membrane.
- Warm-floor zones under DITRA-HEAT that stop heating. The heating cable’s cold lead is usually the failed part, not the field cable. That’s a small, targeted repair if the installer left a service loop; expensive if not.
- Bubbling paint or a soft baseboard on the wall behind a shower. The KERDI pan seal at the drain flange or a missed corner gasket is letting water travel. This is the failure most owners miss for months.
- Grout eroding at floor perimeter near walls. The SCHIENE or RONDEC movement profile at the perimeter isn’t allowing expansion. It’s cosmetic until the water gets past the membrane, which in a wet shower happens slowly and then quickly.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

On this page we use bathroom remodel numbers, since Schluter systems live under almost every tile surface in a wet room. Here’s what you can expect in Long Beach:
| Scope | Installed range |
|---|---|
| Bathroom remodel (full) | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation (KERDI-SHOWER-ready) | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
| Bathroom vanity installation | $800 – $3,000 |
What drives the range: how much membrane gets replaced vs. reused (we don’t reuse Schluter membrane once it’s compromised), tile size and type, whether the subfloor needs work, drain relocation, and heated floor inclusion. The price is written before any demo. If Schluter material costs come in higher, that’s on us, not on the invoice. Every project carries our 365-Day Done Right Promise in writing: if the waterproofing or tile installation fails inside that window, we come back and make it right at no charge.
DIY or Call Us?
Some checks you can do safely. Some work you shouldn’t touch. Here’s the honest split:
Safe for you to check: measure your KERDI-BOARD thickness for a replacement panel order, read the model number off your DITRA-HEAT thermostat, verify which profile series is at your tile edge, and look for visible water staining in the wall behind the shower.
Where DIY goes wrong: Schluter is a system, and every part of it depends on the others. Laying new KERDI-BAND over a failed band without stripping the old thin-set to bare board creates a leak. Re-tiling over DITRA membrane without cleaning and re-priming the fleece is a guaranteed failure within a year in Long Beach’s humid coastal air. If the floor is heated, pulling tile near a DITRA-HEAT cable to inspect it has a strong chance of nicking the element – and a nicked cable means a new floor.
If you’re not sure which failure you have, that’s exactly the call worth making. Call (833) 510-6967 – a live person answers, we schedule a free evaluation, and you get a written price before anything gets touched.
FAQs

Properly installed KERDI and DITRA in a Long Beach shower routinely last 25+ years – the membrane itself doesn’t degrade. What fails is the installation: thin-set bond at seams, band application, and drain-flange sealing. If those were done right, the system outlasts the tile. If they weren’t, failure typically shows up between year 3 and year 8.
Sometimes, yes – and we’ll tell you when. A failed KERDI-BAND at one seam or a single DITRA-HEAT thermostat is a repair, not a remodel. A compromised shower pan or failed DITRA under load-bearing tile is not worth trying to patch; we’ll show you why with photos before quoting a replacement. Call (833) 510-6967 to walk through the situation.
A targeted repair (band replacement, thermostat, drain body) typically takes 1 – 3 days including cure time. A full shower rebuild with KERDI-SHOWER and new tile runs 5 – 10 working days. A full floor replacement with DITRA-HEAT and tile runs 4 – 8 working days depending on square footage. We give you a real timeline in writing, and we arrive in the window we promised.
DITRA, KERDI, KERDI-BOARD, and KERDI-SHOWER come through established Schluter distributors, sourced to the exact series and profile number matching your system. We don’t carry Schluter stock on any truck – each job is ordered to spec, which is why a compatibility check is the first step on every quote. Your written estimate breaks out the materials line-by-line, so you see what you’re buying. We also source KraftMaid, Cambria, and Silestone for the vanity and countertop side of a bathroom remodel when the project calls for it.
Call (833) 510-6967 for a free estimate. A live person answers any hour, and you’ll have a written number in hand before a single tile comes up – that’s The Kingswell Way.
Written by the team at Penhallow Remodeling Long Beach, serving Long Beach and nearby areas.












