







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The Long Beach Owner’s Guide
If you have a Schluter system in a Long Beach addition or ADU and the tile, waterproofing, or uncoupling layer has started to fail, the fix is almost always a system-compatible replacement part installed correctly, not a cosmetic patch. For an addition or ADU project, that work runs $45,000 – $130,000 in Long Beach depending on the addition size, whether it is an attached room or a freestanding unit, and the system that failed. We are an independent service provider, not affiliated with Schluter; we install and repair Schluter-compatible assemblies, and we quote the work in writing before anything starts.
Owners usually find the failure the same way. A hairline crack tracks along a grout line in a new basement bath. A tile “sounds hollow” underfoot near a shower bench. Or the tile edge on an ADU stoop starts lifting after a wet winter. By the time you can see it, the failure underneath has usually been moving for a season.
Key Takeaways
- System failures in additions and ADUs trace to three parts more than any other: the waterproofing membrane, the uncoupling or bonding mat, and the movement joint profiles.
- Long Beach’s marine air and clay-heavy soils put real stress on these assemblies, so part choice matters as much as installation.
- Everything we install carries a written price up front and a 365-Day Done Right Promise. If it fails inside that year, we come back and fix it at no charge.
Which Schluter Models This Applies To

Schluter is a family of systems, not one product, so the “part” that failed depends on which assembly is in your addition or ADU. The common ones:
- DITRA and DITRA-HEAT – uncoupling membrane for tile floors. DITRA comes in 3 mm and 5 mm thicknesses; DITRA-HEAT adds the wire. Size and format matter for matching an existing field.
- KERDI and KERDI-BAND – the waterproofing membrane and seam banding for showers and wet areas. KERDI comes in multiple widths (often 3’3″ and 4’11” rolls), and the seam banding must match the membrane system.
- KERDI-BOARD – the waterproof backer board, in 1/2″ and 2″ thicknesses. The board thickness changes your clearance to the wall.
- DILEX and SCHIENE – movement joints and edge profiles. DILEX handles movement; SCHIENE is an edging trim. The profile height must match your tile thickness, or the edge sits proud.
How to identify the right part: read the printed markings on the membrane back, the box, or the profile’s printed code. Then measure. A 5 mm DITRA will not match a 3 mm field, and a profile sized for 3/8″ tile looks wrong on 1/2″. Original Schluter parts and quality equivalents both work when the spec matches, but the OEM route is worth it when you are matching an existing field you cannot see under the finished floor. We do not stock parts and do not carry them on a truck; we source the correct part for your build and install it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
- Hollow sounds underfoot. Tap the tile in a grid. A dull, hollow ring means the tile lost bond to the uncoupling mat, usually from a mat that was not fully embedded in thin-set. Left alone, the tile pops.
- Grout cracking along a straight line. Movement cracking runs along joints or wall transitions. In a Long Beach ADU on a raised foundation, this often shows the whole assembly is flexing, not just the grout.
- Soft spots or efflorescence near a shower or wet wall. White mineral bloom or a damp grout line points to failed KERDI waterproofing at a seam. Water is getting behind the tile and the band failed.
- A lifted or loose edge profile. When a DILEX or SCHIENE trim starts to lift, the profile was likely sized wrong or set with poor thin-set contact. It will keep working loose and can catch a bare foot.
- Tile tenting near a sun-exposed slab. Full-scale tenting happens when there is no movement joint and the assembly expands. Long Beach’s warm, sunny slab edges are a common place for it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

A targeted Schluter system repair inside a Long Beach addition or ADU usually runs a few hundred to a few thousand dollars for the part and the labor to set it, but the realistic number starts with the scope. If a whole room has to be stripped, re-waterproofed, and re-tiled, the work sits in the range of a full addition or ADU project: $45,000 – $130,000.
What drives the range: how much tile and system comes up, whether the waterproofing has to be rebuilt to the current standard, the part and its format, and whether a shower or wet area is involved. What sits inside that price with us:
- The correct Schluter-compatible part, sourced for your build.
- Labor to remove the failed assembly, prep, install, and finish.
- Written quote before any work starts, so the number on day one is the number on the invoice.
- A written guarantee on the repair, plus the 365-Day Done Right Promise.
We also install KraftMaid cabinetry and Cambria, Silestone, and Caesarstone countertops when an addition or ADU includes a kitchen or bath, so the same written price and guarantee covers the whole build.
DIY or Call Us?
There are things you can safely check. Tap the tile to map hollow spots. Read and write down the printed code on the membrane or profile. Photograph the cracked grout line and measure the tile thickness. None of that risks damage.
Where it goes wrong: stripping a KERDI or DITRA assembly means you have to restore the waterproofing correctly, and a seam that is not fully banded will leak behind the tile and rot the framing. Setting a DITRA or KERDI assembly in the wrong thin-set coverage causes the same failure again, only faster. This is not a dangerous part like a garage spring, but it is unforgiving work. The wrong install fails the same way the old one did. Call (833) 510-6967 and let us assess the failed system first. The estimate is free, and we give a written price before we touch anything.
FAQs

How long should a Schluter waterproofing or uncoupling system last in a Long Beach addition?
Installed and maintained correctly, a KERDI or DITRA assembly should last the life of the tile. The part itself rarely fails; the seam, the bond, or a missing movement joint is what fails. Long Beach’s marine air and clay soils put real movement on additions, so how it was installed matters more than the part. Call (833) 510-6967 for an exact quote; estimates are free.
Can it be repaired instead of replaced?
Often, yes. A single hollow tile or a failed edge profile can be repaired without redoing the whole floor. If the waterproofing membrane has failed across a wet area or the whole assembly is tenting, replacement is the honest answer. We inspect and tell you which one it is before quoting. Call (833) 510-6967 for a free estimate.
How long does the swap take?
A single profile or one-tile repair is a short day. A shower or wet area re-waterproofed and re-tiled usually runs several days, with curing time before the finish goes on. A full addition or ADU re-do depends on scope. We give you the real number in the written quote. Call (833) 510-6967 to schedule.
How do you source the part?
We match the printed code and the measured thickness to the exact Schluter-compatible part your assembly needs, then source it from trade channels. We do not stock parts locally and do not carry them on a truck. If you need it in hand fast, the written quote tells you the lead time. Call (833) 510-6967 for a free estimate.
If a Schluter system in your Long Beach addition or ADU is showing hollow tiles, cracked grout, or a loose profile, we will look at the actual failure, quote the repair in writing, and stand behind it with our 365-Day Done Right Promise and a free return visit if the repair fails. Call (833) 510-6967 for a free estimate.
Written by the team at Penhallow Remodeling Long Beach, serving Long Beach and nearby areas.












